Getting Started: Brewing Equipment Needed

  • Stainless Steel Stockpot: Try to get one that can carry 16-20 quarts (15-19L). It is also advised to purchase one with sturdy handles that are attached to the actual pot itself.


  • Thermometer: Try to get a glass thermometer because they float upright in your must so you can read it easily. Just be careful when losing it because if it breaks while in your must then the whole batch is ruined. A good idea is to get a thermometer that ranges from 50 degrees F to 200 degrees F in increments of 10 degrees F or less.


  • Hydrometer: This instruments reads how much sugar is dissolved in the solution using specific gravity. “Pure water at a temperature of 68 degrees F (20 degrees C) has a specific gravity of 1.000. Adding sugar makes the density of the solution-and therefore the specific gravity-rise. When this occurs, the hydrometer floats higher in the solution changing where its scale will be read” (Schramm 28).


  • Plastic fermenter: The plastic fermentation buckets ranges from 5-8 gallons. There should be a hole on the top of the lid for the stopper and airlock. The reason plastic is desired because plastic fermenters won’t break or melt when the hot honey is added. However, if the interior is scratched then there is a potential for bacterial growth.


  • Glass carboy: The carboys come in 5-10 gallon glass bottles that do not scratch easily but if dropped, can break and ruin your batch as well as harm you. This is why some people use rubber carboy handles to ease the lifting and transferring process. Plastic carboys like Better Bottles are made from clear, stain resistant, non-porous PET plastic that’s impermeable to oxygen. Just be careful when cleaning to prevent scratching.


  • Airlocks: These locks provide the barrier that prevents contaminating bacteria or wild yeast from entering the fermenter and mead while allowing carbon dioxide to escape from the actively fermenting mead. The two most common are the Bubbler Air Lock and the Three-Piece Airlock. The Three-Piece Airlock is generally used for primary fermentation because if there is an overactive batch that foams all the way to the top of the fermenter to the airlock, it is easier to clean the separate pieces. In addition the Three-Piece is resistant to “suck-back” where negative pressure in the fermenter causes the third piece to suck down on the gas tube. With the Bubbler, the “suck-back” will draw all the airlock fluid into the wort. The Bubbler is used in the secondary fermentation because it allows a more accurate visualization of carbon dioxide escaping. If you don’t feel like purchasing an airlock or if you’re from the ghetto, insert a hose into the rubber stopper in your fermentation bucket and place the other end into a sanitized jaw filled with fluid (this method is most helpful when you are making a large batch or if your batch has vigorous fermentation). Another tip is to purchase an airlock brush to clean the fermentation residue out of the airlocks.


  • Drilled Rubber Stoppers: This is used to adjoin your fermenter with the airlock. Stoppers No. 6 and 7 work well with 5 gallon carboys. If you are using carboys of a different size consult with the homebrew shop about the stopper size you need.


  • Siphon Hose: You need clear, food-grade vinyl tubing with a 5/16 inch and 3/8 inch inner diameter. It is best to get one that is six feet long so there is leeway when re-racking. It is good to replace the siphon every 6 months to ensure sanitation.


  • Racking Cane: This is a “clear, hard plastic food-grade tubing bent at an angle near one end. The siphon hose fits snugly over the end and the cane is lowered into the mead to be racked, to provide you control over siphoning. This allows you to avoid the sediment pack or fruit residue…” (Schramm 29).
  • Sanitizer: I prefer Star San for the sanitizer. You can buy it in any hombrew shop or website. I tend to buy the 32 oz because I know I will always need this. If you have a deep kitchen sink (preferably two), clean one sink thoroughly (and I mean scrub all that food residue) and then use the drain stopper. Add the Star San and fill that sink with water. You then have a basin designated to sanitizing your equipment.


  • Cleaner: After re-racking your mead, there will be a thick layer of sediment in your carboy. PBW (Powdered Brewery Wash) is an alkali cleaner which if left overnight in the carboy, will require no scrubbing the following morning. It is also advised to purchase a carboy brush, preferably 24” long and bent at a 90 degree angle to reach all the corners of the carboy’s interior. There are also brushes that attach to a drill bit to ensure a faster more efficient cleaning method.


  • Bottle Tree: Although you won’t need this when brewing your mead, you will find this useful when it comes time to bottling. Buy one that comes with a carrying handle on top. It makes drying your bottles easier and more efficient.


  1. GotMead
  2. Northern Brewer

Getting Started: Bottling Equipment

Here is a link to the page of shops suggested to purchase brewing equipment.

The following list was found in Ken Schramm’s The Complete Meadmaker:

  1. Bottle Filler: This stops the flow of mead into your bottles as you fill them. They use a valve to cut off the flow, closed either by spring or gravity.


2. Bottle Cappers: There are two different types of cappers-the Bench Capper and Lever Capper. Bench cappers sit on a bench, table, or floor, and press the cap down onto the bottle using a single handle. They are easier to use only wen the bottles are uniform in size. Lever Cappers have two or three claws that squeeze the cap down. However they do not work well on bottles with large diameter necks.

Lever Capper Lever Capper

3. Bottle Brush or Bottle Washer: All bottles should be cleaned prior use. A jet bottle washer attaches to the spigot above your sink and channels the water flow into a copper pipe with a valve. A bottle is pressed upside down over the pipe to release the jet of water. But if you have really dirty bottles then a bottle brush is more suitable.



4. Bottles: 5 gallon batches of mead fill about 53 12oz bottles or 25 750ml Champagne-style wine bottles. American sparkling wine bottles are great to recycle as mead bottles because they will accept a crown cap and can withstand the pressures that build up in a sparkling mead. Avoid using regular wine bottles because if your fermentation is not complete it can result in glass breakage.

Sanitized bottles with some foam

Sanitized bottles with some foam

5. Bottle Caps: Crown caps are the easiest and most economical choice. They come uncrimped.

6. Siphon Pump: Used to transfer beer from kettle to carboy, or carboy to carboy.


However I if you choice to use the corking method rather than capping, then you need the additional following:

  1. Italian Double Lever Corker


  1. Corks: Using corks will allow some oxygen to seem into the bottle, a process that is called micro-oxygenation. This can benefit the flavor of the mead.